Table of Contents

Kamailio 3.0: Core Cookbook

This tutorial collects the functions and parameters exported by Kamailio 3.0 core to configuration file. (Note: if you can't find what you're looking for here, try NEWS file on GIT at sip-router.org, which contains an up-to-date list of features and script commands).

Note: Kamailio 3.0 uses SIP Router core framework and has the sources hosted in GIT repository at http://sip-router.org Note: The parameters on this page are NOT in alphabetical order.

Config Pre-Processor Directives

include_file

 include_file "path_to_file"

Include the content of the file in config before parsing. path_to_file must be a static string. Including file operation is done at startup. If you change the content of included file, you have to restart the SIP server to become effective.

The path_to_file can be relative or absolute. If it is not absolute path, first attempt is to locate it relative to current directory, and if fails, relative to directory of the file that includes it. There is no restriction where include can be used or what can contain - any part of config file is ok. There is a limit of maximum 10 includes in depth, otherwise you can use as many includes as you want. Reporting of the cfg file syntax errors prints now the file name for easier troubleshooting.

Example of usage:

route {
    ...
    include_file "/sr/checks.cfg"
    ...
}
 
--- /sr/checks.cfg ---
 
   if (!mf_process_maxfwd_header("10")) {
       sl_send_reply("483","Too Many Hops");
       exit;
   }
 
---

define

Control in C-style what parts of the config file are executed. The parts in non-defined zones are not loaded, ensuring lower memory usage and faster execution.

Available directives:

Among benefits:

Example: how to make config to be used in two environments, say testbed and production, controlled just by one define to switch between the two modes:

...
 
#!define TESTBED_MODE
 
#!ifdef TESTBED_MODE
  debug=5
  log_stderror=yes
  listen=192.168.1.1
#!else
  debug=2
  log_stderror=no
  listen=10.0.0.1
#!endif
 
...
 
#!ifdef TESTBED_MODE
modparam("acc|auth_db|usrloc", "db_url",
	"mysql://openser:openserrw@localhost/openser_testbed")
#!else
modparam("acc|auth_db|usrloc", "db_url",
	"mysql://openser:openserrw@10.0.0.2/openser_production")
#!endif
 
...
 
#!ifdef TESTBED_MODE
route[DEBUG] {
  xlog("SCRIPT: SIP $rm from: $fu to: $ru - srcip: $si"\n);
}
#!endif
 
...
 
route {
#!ifdef TESTBED_MODE
  route(DEBUG);
#!endif
 
  ...
}
 
...

NB Text on the same line after the directive will cause problems. Keep the directive lines clean and only comment on a line before or after.

Core Keywords

Keywords specific to SIP messages which can be used mainly in 'if' expressions.

af

The address family of the received SIP message. It is INET if the message was received over IPv4 or INET6 if the message was received over IPv6.

Exampe of usage:

    if (af==INET6) {
        log("Message received over IPv6 link\n");
    }

dst_ip

The IP of the local interface where the SIP message was received. When the proxy listens on many network interfaces, makes possible to detect which was the one that received the packet.

Example of usage:

   if(dst_ip==127.0.0.1) {
      log("message received on loopback interface\n");
   };

dst_port

The local port where the SIP packet was received. When SIP-Router is listening on many ports, it is useful to learn which was the one that received the SIP packet.

Example of usage:

   if(dst_port==5061)
   {
       log("message was received on port 5061\n");
   };

from_uri

This script variable is a reference to the URI of 'From' header. It can be used to test 'From'- header URI value.

Example of usage:

    if(is_method("INVITE") && from_uri=~".*@sip-router.org")
    {
        log("the caller is from sip-router.org\n");
    };

method

The variable is a reference to the SIP method of the message.

Example of usage:

    if(method=="REGISTER")
    {
       log("this SIP request is a REGISTER message\n");
    };

msg:len

The variable is a reference to the size of the message. It can be used in 'if' constructs to test message's size.

Example of usage:

    if(msg:len>2048)
    {
        sl_send_reply("413", "message too large");
        exit;
    };

.

proto

This variable can be used to test the transport protocol of the SIP message.

Example of usage:

    if(proto==UDP)
    {
        log("SIP message received over UDP\n");
    };

status

If used in onreply_route, this variable is a referece to the status code of the reply. If it used in a standard route block, the variable is a reference to the status of the last reply sent out for the current request.

Example of usage:

    if(status=="200")
    {
        log("this is a 200 OK reply\n");
    };

snd_af

snd_ip

snd_port

snd_proto

src_ip

Reference to source IP address of the SIP message.

Example of usage:

    if(src_ip==127.0.0.1)
    {
        log("the message was sent from localhost!\n");
    };

src_port

Reference to source port of the SIP message (from which port the message was sent by previous hop).

Example of usage:

    if(src_port==5061)
    {
        log("message sent from port 5061\n");
    }

to_ip

to_port

to_uri

This variable can be used to test the value of URI from To header.

Example of usage:

  if(to_uri=~"sip:.+@sip-router.org")
  {
      log("this is a request for sip-router.org users\n");
  };

uri

This variable can be used to test the value of the request URI.

Example of usage:

    if(uri=~"sip:.+@sip-router.org")
    {
        log("this is a request for sip-router.org users\n");
    };

Core Values

Values that can be used in 'if' expressions to check against Core Keywords

INET

This keyword can be used to test whether the SIP packet was received over an IPv4 connection.

Example of usage:

    if (af==INET) {
        log("the SIP message was received over IPv4\n");
    }

INET6

This keyword can be used to test whether the SIP packet was received over an IPv6 connection.

Example of usage:

  if(af==INET6)
  {
      log("the SIP message was received over IPv6\n");
  };

TCP

This keyword can be used to test the value of 'proto' and check whether the SIP packet was received over TCP or not.

Example of usage:

  if(proto==TCP)
  {
      log("the SIP message was received over TCP\n");
  };

UDP

This keyword can be used to test the value of 'proto' and check whether the SIP packet was received over UDP or not.

Example of usage:

  if(proto==UDP)
  {
      log("the SIP message was received over UDP\n");
  };

max_len

Note: This command was removed.

myself

It is a reference to the list of local IP addresses, hostnames and aliases that has been set in SIP-Router configuration file. This lists contain the domains served by SIP-Router.

The variable can be used to test if the host part of an URI is in the list. The usefulness of this test is to select the messages that has to be processed locally or has to be forwarded to another server.

See “alias” to add hostnames,IP addresses and aliases to the list.

Example of usage:

    if(uri==myself) {
        log("the request is for local processing\n");
    };

Core parameters

advertised_address

It can be an IP address or string and represents the address advertised in Via header and other destination lumps (e.g RR header). If empty or not set (default value) the socket address from where the request will be sent is used.

WARNING: 
- don't set it unless you know what you are doing (e.g. nat traversal)
- you can set anything here, no check is made (e.g. foo.bar will be accepted even if foo.bar doesn't exist)

Example of usage:

  advertised_address="sip-router.org"

advertised_port

The port advertised in Via header and other destination lumps (e.g. RR). If empty or not set (default value) the port from where the message will be sent is used. Same warnings as for 'advertised_address'.

Example of usage:

  advertised_port=5080

alias

Parameter to set alias hostnames for the server. It can be set many times, each value being added in a list to match the hostname when 'myself' is checked.

It is necessary to include the port (the port value used in the “port=” or “listen=” defintions) in the alias definition otherwise the loose_route() function will not work as expected for local forwards. Even if you do not use 'myself' explicitly (for example if you use the domain module), it is often necessary to set the alias as these aliases are used by the loose_routing function and might be needed to handle requests with pre-loaded route set correctly.

Example of usage:

    alias=other.domain.com:5060
    alias=another.domain.com:5060

check_via

Check if the address in top most via of replies is local. Default value is 0 (check disabled).

Example of usage:

  check_via=1 

children

Number of children to fork for the UDP interfaces (one set for each interface - ip:port). Default value is 8. For example if you configure the proxy to listen on 3 UDP ports, it will create 3xchildren processes which handle the incoming UDP messages.

For configuration of the TCP/TLS worker threads see the option “tcp_children”.

Example of usage:

  children=16

chroot

The value must be a valid path in the system. If set, SIP server will chroot (change root directory) to its value.

Example of usage:

  chroot=/other/fakeroot

debug

Set the debug level. Higher values make SIP server to print more debug messages.

Examples of usage:

  debug=3 -- print only important messages (like errors or more critical situations), recommended for running proxy as daemon
  debug=9 -- print a lot of debug messages - use it only when doing debugging sessions

The 'debug' parameter is usually used in concordance with 'log_stderror' parameter.

Value of 'debug' parameter can also be get and set dynamically using 'debug' Core MI function.

For more see: http://www.kamailio.org/dokuwiki/doku.php/tutorials:debug-syslog-messages

description

Alias name: descr desc

disable_core_dump

Can be 'yes' or 'no'. By default core dump limits are set to unlimited or a high enough value. Set this config variable to 'yes' to disable core dump-ing (will set core limits to 0).

Default value is 'no'.

Example of usage:

  disable_core_dump=yes

disable_tls

Alias name: tls_disable

Global parameter to disable TLS support in the SIP server. Default value is 'no'.

Note: Make sure to load the “tls” module to get tls functionality.

Example of usage:

  disable_tls=yes

In Kamailio 3.0 TLS is implemented as a module. Thus, the TLS configuration is done as module configuration. For more details see the README of the TLS module: http://sip-router.org/docbook/sip-router/branch/master/modules/tls/tls.html

enable_tls

Alias name: tls_enable

Reverse Meaning of the disable_tls parameter. See disable_tls parameter.

enable_tls=yes # enable tls support in core

exit_timeout

Alias name: ser_kill_timeout

How much time ser will wait for all the shutdown procedures to complete. If this time is exceeded, all the remaining processes are immediately killed and ser exits immediately (it might also generate a core dump if the cleanup part takes too long).

Default: 60 s. Use 0 to disable.

 exit_timeout = seconds

flags

Alias name: bool

force_rport

yes/no: Similar to the force_rport() function, but activates symmetric response routing globally.

fork

If set to 'yes' the proxy will fork and run in daemon mode - one process will be created for each network interface the proxy listens to and for each protocol (TCP/UDP), multiplied with the value of 'children' parameter.

When set to 'no', the proxy will stay bound to the terminal and runs as single process. First interface is used for listening to. This is equivalent to setting the server option “-F”.

Default value is 'yes'.

Example of usage:

  fork=no

group

Alias name: gid

The group id to run Kamailio.

Example of usage:

group="siprouter"

listen

Set the network addresses the SIP server should listen to. It can be an IP address, hostname or network iterface id or combination of protocol:address:port (e.g., udp:10.10.10.10:5060). This parameter can be set multiple times in same configuration file, the server listening on all addresses specified.

Example of usage:

  listen=10.10.10.10
  listen=eth1:5062
  listen=udp:10.10.10.10:5064

If you omit this directive then the SIP server will listen on all interfaces. On start the SIP server reports all the interfaces that it is listening on. Even if you specify only UDP interfaces here, the server will start the TCP engine too. If you don't want this, you need to disable the TCP support completly with the core parameter disable_tcp.

If you specify IPv6 addresses, you should put them into square brackets, e.g.:

  listen=udp:[2a02:1850:1:1::13]:5060

loadmodule

Loads a module for later usage in the configuration script. The modules is searched in the path specified by loadpath.

Prototype: loadmodule “modulepath”

If modulepath is only modulename or modulename.so, then SIP Router will try to search also for modulename/modulename.so, very useful when usining directly the version compiled in the source tree.

Example of usage:

    loadpath "/usr/local/lib/kamailio/:usr/local/lib/kamailio/modules/"
 
    loadmodule "/usr/local/lib/kamailio/modules/db_mysql.so"
    loadmodule "modules_k/usrloc.so"
    loadmodule "tm"
    loadmodule "dialplan.so"

loadpath

Alias name: mpath

Set the module search path. loadpath takes a list of directories separated by ':'. The list is searched in-order. For each directory d, $d/${module_name}.so and $d/${module_name}/${module_name}.so are tried.

This can be used to simplify the loadmodule parameter and can include many paths separated by colon. First module found is used.

Example of usage:

    loadpath "/usr/local/lib/kamailio/modules:/usr/local/lib/kamailio/modules_k"
 
    loadmodule "mysql"
    loadmodule "uri"
    loadmodule "uri_db"
    loadmodule "sl"
    loadmodule "tm"

The proxy tries to find the modules in a smart way, e.g: loadmodule “uri” tries to find uri.so in the loadpath, but also uri/uri.so.

If you have installed Kamailio and ser modules, and want to load them in a certain order, you can for example use the following technique:

# common modules
loadpath "/usr/lib/kamailio/modules"
loadmodule "db_mysql"
...

# Kamailio modules
loadpath "/usr/lib/kamailio/modules_k"
loadmodule "cfgutils"
... 

# ser modules
loadpath "/usr/lib/kamailio/modules_s"
loadmodule "ctl"
...

log_facility

If Kamailio logs to syslog, you can control the facility for logging. Very useful when you want to divert all Kamailio logs to a different log file. See the man page syslog(3) for more details.

For more see: http://www.kamailio.org/dokuwiki/doku.php/tutorials:debug-syslog-messages

Default value is LOG_DAEMON.

Example of usage:

  log_facility=LOG_LOCAL0

log_name

Allows to configure a log_name prefix which will be used when printing to syslog. This is useful to filter log messages when running many instance of Kamailio on same server

log_stderror

With this parameter you can make Kamailio to write log and debug messages to standard error. Possible values are:

- “yes” - write the messages to standard error

- “no” - write the messages to syslog

Default value is “no”.

For more see: http://www.kamailio.org/dokuwiki/doku.php/tutorials:debug-syslog-messages

Example of usage:

  log_stderror=yes

maxbuffer

The size in bytes not to be exceeded during the auto-probing procedure of descovering the maximum buffer size for receiving UDP messages. Default value is 262144.

Example of usage:

  maxbuffer=65536

max_while_loops

The parameters set the value of maximum loops that can be done within a “while”. Comes as a protection to avoid infinite loops in config file execution. Default is 100.

Example of usage:

  max_while_loops=200

mcast_loopback

It can be 'yes' or 'no'. If set to 'yes', multicast datagram are sent over loopback. Default value is 'no'.

Example of usage:

  mcast_loopback=yes

mcast_ttl

Set the value for multicast ttl. Default value is OS specific (usually 1).

Example of usage:

  mcast_ttl=32

memdbg

Alias name: mem_dbg

memlog

Alias name: mem_log

Log level to print memory debug info. It has be less than the value of 'debug' parameter if you want memory info to be logged. Default: memlog=L_DBG (4)

Example of usage:

    memlog=2

mem_summary

What details to print when dumping memory allocation status. The value is a bitmask of:

Example of usage:

    mem_summary=2

mhomed

Set the server to try to locate outbound interface on multihomed host. This parameter affects the selection of the outgoing socket for forwarding requests. By default is off (0) - it is rather time consuming. When decativated, the incoming socket will be used or the first one for a different protocol, disregarding the destination location. When activated, Kamailio will select a socket that can reach the destination (to be able to connect to the remote address). (Kamailio opens a UDP socket to the destination, then it retrieves the local IP which was assigned by the operating system to the new UDP socket. Then this socket will be closed and the retrieved IP address will be used as IP address in the Via/Record-Route headers)

Example of usage:

  mhomed=1

mlock_pages

Locks all ser pages into memory making it unswappable (in general one doesn't want his sip proxy swapped out :-))

mlock_pages = yes |no (default no)

modparam

The modparam command will be used to set the options of the modules.

Example:

modparam("usrloc", "db_mode", 2)
modparam("usrloc", "nat_bflag", 6)

See the documenation of the respective module to find out the available options.

open_files_limit

If set and bigger than the current open file limit, Kamailio will try to increase its open file limit to this number. Note: Kamailio must be started as root to be able to increase a limit past the hard limit (which, for open files, is 1024 on most systems).

Example of usage:

  open_files_limit=2048

phone2tel

By enabling this feature, SIP-Router internally treats SIP URIs with user=phone parameter as TEL URIs. If you do not want thi behavior, you have to turn it off.

Default value: 1 (enabled)

phone2tel = 0

pmtu_discovery

If enabled, the Don't Fragment (DF) bit will be set in outbound IP packets.

pmtu_discovery = 0 | 1 (default 0)

port

The port the SIP server listens to. The default value for it is 5060.

Example of usage:

  port=5080

reply_to_via

If it is set to 1, any local reply is sent to the IP address advertised in top most Via of the request instead of the IP address from which the request was received. Default value is 0 (off).

Example of usage:

  reply_to_via=0

server_id

A configurable unique server id that can be used to discriminate server instances within a cluster of servers when all other information, such as IP addresses are the same.

  server_id = number

server_header

Set the value of Server header for replies generated by SIP router. It must contain the header name, but not the ending CRLF.

Example of usage:

server_header="Server: My Super SIP Server"

server_signature

This parameter controls the “Server” header in any locally generated message.

Example of usage:

   server_signature=no

If it is enabled (default=yes) a header is generated as in the following example:

   Server: SIP Router (<version> (<arch>/<os>))

shm_force_alloc

Tries to pre-fault all the shared memory, before starting. When “on”, start time will increase, but combined with mlock_pages will guarantee ser will get all its memory from the beginning (no more kswapd slow downs)

shm_force_alloc = yes | no (default no)

sip_warning

Can be 0 or 1. If set to 1 (default value) a 'Warning' header is added to each rely generated by Kamailio. The header contains several details that help troubleshooting using the network traffic dumps, but might reveal details of your network infrastructure and internall SIP routing.

Example of usage:

  sip_warning=0

statistics

stun_allow_fp

Use FINGERPRINT attribute in STUN server

stun_allow_fp = 0 | 1 (off | on); default: 1

stun_allow_stun

Use STUN or not (works only if Kamailio was compiled with STUN support)

stun_allow_stun = 0 | 1 (off | on); default 1

stun_refresh_interval

Value for the REFRESH INTERVAL attribute of the internal STUN server

 stun_refresh_interval = number in millisecond (default 0)

syn_branch

The parameter controls how the branch parameter is calculated for stateless forwarding.

If syn_branch is turned off, calculation is derived from transaction key, i.e., as an md5 of From/To/CallID/ CSeq exactly the same way as TM does. This is good for reboot - than messages belonging to transaction lost due to reboot will still be forwarded with the same branch parameter and will be match-able downstream.

If it is turned on, just a simple value is put into the branch paramter (better for performance)

tos

The TOS (Type Of Service) to be used for the sent IP packages (both TCP and UDP).

Example of usage:

  tos=IPTOS_LOWDELAY
  tos=0x10
  tos=IPTOS_RELIABILITY

udp_mtu

Fallback to another protocol (udp_mtu_try_proto must be set also either globally or per packet) if the constructed request size is greater then udp_mtu.

RFC 3261 specified size: 1300. Default: 0 (off).

udp_mtu = number

udp_mtu_try_proto

If udp_mtu !=0 and udp forwarded request size (after adding all the “local” headers) > udp_mtu, use this protocol instead of udp. Only the Via header will be updated (e.g. The Record-Route will be the one built for udp).

Warning: Although RFC3261 mandates automatic transport protocol changing, enabling this feature can lead to problems with clients which do not support other protocols or are behind a firewall or NAT. Use this only when you know what you do!

See also udp_mtu_try_proto(proto) function.

Default: UDP (off). Recommended: TCP.

udp_mtu_try_proto = TCP|TLS|SCTP|UDP

user

Alias name: uid

The user id to run Kamailio (Kamailio will suid to it).

Example of usage:

    user="siprouter"

user_agent_header

Set the value of User-Agent header for requests generated by SIP router. It must contain header name as well, but not the ending CRLF.

user_agent_header="User-Agent: My Super SIP Server"

workdir

Alias name: wdir

The working directory used by Kamailio at runtime. You might find it usefull when come to generating core files :)

Example of usage:

   wdir="/usr/local/siprouter"
   or
   wdir=/usr/openser_wd

DNS Parameters

SIP-Router allows you to finetune the DNS resolver settings.

The maximum time a dns request can take (before failing) is (if dns_try_ipv6 is yes, mutliply it again by 2; if SRV and NAPTR lookups are enabled, it can take even longer!):

(dns_retr_time*(dns_retr_no+1)*dns_servers_no)*(search_list_domains)

Note: During DNS lookups, the process which performs the DNS lookup blocks. To minimize the blocked time the following parameters can be used (max 2s):

dns_try_ipv6=no
dns_retr_time=1
dns_retr_no=1
dns_use_search_list=no

dns

This parameter controls if the SIP server will try doing a DNS lookup on the address in the Via header of a received sip request to decide if adding a received=<src_ip> parameter to the Via is necessary. Note that Vias containing DNS names (instead of IPs) should have received= added, so turning dns to yes is not recommended.

Default is no.

rev_dns

This parameter controls if the SIP server will try doing a reverse DNS lookup on the source IP of a sip request to decide if adding a received=<src_ip> parameter to the Via is necessary (if the Via contains a DNS name instead of an IP address, the result of the reverse dns on the source IP will be compared with the DNS name in the Via). See also dns (the effect is cumulative, both can be turned on and in that case if the DNS lookup test fails the reverse DNS test will be tried). Note that Vias containing DNS names (instead of IPs) should have received= added, so turning rev_dns to yes is not recommended.

Default is no.

dns_cache_del_nonexp

Alias name: dns_cache_delete_nonexpired

dns_cache_del_nonexp = yes | no (default: no) 
  allow deletion of non-expired records from the cache when there is no more space
  left for new ones. The last-recently used entries are deleted first.

dns_cache_flags

dns_cache_flags = number (default 0) - 
  dns cache specific resolver flags, used for overriding the default behaviour (low level).
  Possible values:
    1 - ipv4 only: only DNS A requests are performed, even if ser listens also on ipv6 addresses.
    2 - ipv6 only: only DNS AAAA requests are performed. Ignored if dns_try_ipv6 is off or ser 
        doesn't listen on any ipv6 address.
    4 - prefer ipv6: try first to resolve a host name to an ipv6 address (DNS AAAA request) and only
        if this fails try an ipv4 address (DNS A request). By default the ipv4 addresses are preferred.

dns_cache_gc_interval

Interval in seconds after which the dns cache is garbage collected (default: 120 s)

dns_cache_gc_interval = number

dns_cache_init

If off, the dns cache is not initialized at startup and cannot be enabled runtime, that saves some memory.

dns_cache_init = on | off (default on)

dns_cache_max_ttl

dns_cache_max_ttl = time in seconds (default MAXINT)

dns_cache_mem

Maximum memory used for the dns cache in KB (default 500 K)

dns_cache_mem = number

dns_cache_min_ttl

dns_cache_min_ttl = time in seconds (default 0)

dns_cache_negative_ttl

Tells how long to keep negative DNS responses in cache. If set to 0, disables caching of negative responses. Default is 60 (seconds).

dns_retr_no

Number of dns retransmissions before giving up. Default value is system specific, depends also on the '/etc/resolv.conf' content (usually 4).

Example of usage:

  dns_retr_no=3

dns_retr_time

Time in seconds before retrying a dns request. Default value is system specific, depends also on the '/etc/resolv.conf' content (usually 5s).

Example of usage:

  dns_retr_time=3

dns_search_full_match

When name was resolved using dns search list, check the domain added in the answer matches with one from the search list (small performance hit, but more safe)

dns_search_full_match = yes | no (default yes)

dns_servers_no

How many dns servers from the ones defined in '/etc/resolv.conf' will be used. Default value is to use all of them.

Example of usage:

  dns_servers_no=2

dns_srv_lb

Alias name: dns_srv_loadbalancing

Enable dns srv weight based load balancing (see doc/dns.txt)

dns_srv_lb = yes | no (default no)

dns_try_ipv6

Can be 'yes' or 'no'. If it is set to 'yes' and a DNS lookup fails, it will retry it for ipv6 (AAAA record). Default value is 'no'.

Note: If dns_try_ipv6 is off, no hostname resolving that would result in an ipv6 address would succeed - it doesn't matter if an actual DNS lookup is to be performed or the host is already an ip address. Thus, if the proxy should forward requests to IPv6 targets, this option must be turned on!

Example of usage:

  dns_try_ipv6=yes

dns_try_naptr

Enable NAPTR support according to RFC 3263 (see doc/dns.txt for more info)

  
dns_try_naptr = yes | no (default no)

dns_sctp_pref, dns_tcp_pref, dns_tls_pref, dns_udp_pref

Alias name: dns_sctp_preference, dns_tcp_preference, dns_tls_preference, dns_udp_preference

Set preference for each protocol when doing naptr lookups. By default dns_udp_pref=30, dns_tcp_pref=20, dns_tls_pref=10 and dns_sctp_pref=20. To use the remote site preferences set all dns_*_pref to the same positive value (e.g. dns_udp_pref=1, dns_tcp_pref=1, dns_tls_pref=1, dns_sctp_pref=1). To completely ignore NAPTR records for a specific protocol, set the corresponding protocol preference to -1 (or any other negative number). (see doc/dns.txt for more info)

dns_{udp,tcp,tls,sctp}_pref = number

dns_use_search_list

Can be 'yes' or 'no'. If set to 'no', the search list in '/etc/resolv.conf' will be ignored (⇒ fewer lookups ⇒ gives up faster). Default value is 'yes'.

HINT: even if you don't have a search list defined, setting this option to 'no' will still be “faster”, because an empty search list is in fact search “” (so even if the search list is empty/missing there will still be 2 dns queries, eg. foo+'.' and oo+“”+'.')

Example of usage:

  dns_use_search_list=no

use_dns_cache

Tells if DNS responses are cached. If set to “off”, disables caching of DNS responses and, as side effect, DNS failover. Default is “on”.

use_dns_failover

use_dns_failover = on | off (default off)

TCP Parameters

The following parameters allows to tweak the TCP behaviour.

disable_tcp

Global parameter to disable TCP support in the SIP server. Default value is 'no'.

Example of usage:

  disable_tcp=yes

tcp_accept_aliases

If a message received over a tcp connection has “alias” in its via a new tcp alias port will be created for the connection the message came from (the alias port will be set to the via one).

Based on draft-ietf-sip-connect-reuse-00.txt, but using only the port (host aliases are dangerous, involve extra DNS lookups and the need for them is questionable)

See force_tcp_alias for more details.

Note: For NAT traversal of TCP clients it is better to not use tcp_accept_aliases but just use nathelper module and fix_nated_[contact|register] functions.

 tcp_accept_aliases= yes|no

tcp_async

Alias name: tcp_buf_write

If enabled, all the tcp writes that would block / wait for connect to finish, will be queued and attempted latter (see also tcp_conn_wq_max and tcp_wq_max).

Note: Using TLS over asynch TCP is not supported at the moment. If you use TLS you have to disable asynch TCP!

tcp_async = yes | no (default yes)

tcp_children

Number of children processes to be created for reading from TCP connections. If no value is explicitly set, the same number of TCP children as UDP children (see “children” parameter) will be used.

Example of usage:

  tcp_children=4

tcp_connection_lifetime

Lifetime in seconds for TCP sessions. TCP sessions which are inactive for >tcp_connection_lifetime will be closed by Kamailio. Default value is defined in tcp_conn.h: #define DEFAULT_TCP_CONNECTION_LIFETIME 120. Setting this value to 0 will close the TCP connection pretty quick ;-). You can also set the TCP lifetime to the expire value of the REGISTER by using the tcp_persistent_flag parameter of Kamailio's registrar module.

Note: As many SIP clients are behind NAT/Firewalls, the SIP proxy should not close the TCP connection as it is not capable of opening a new one.

Example of usage:

  tcp_connection_lifetime=3600

tcp_connect_timeout

Time in seconds before an ongoing attempt to establish a new TCP connection will be aborted. Lower this value for faster detection of TCP connection problems. The default value is 10s.

Example of usage:

  tcp_connect_timeout=5

tcp_conn_wq_max

Maximum bytes queued for write allowed per connection. Attempting to queue more bytes would result in an error and in the connection being closed (too slow). If tcp_write_buf is not enabled, it has no effect.

tcp_conn_wq_max = bytes (default 32 K)

tcp_crlf_ping

Enable SIP outbound TCP keep-alive using PING-PONG (CRLFCRLF - CRLF).

tcp_crlf_ping = yes | no (default: yes)

tcp_defer_accept

Tcp accepts will be delayed until some data is received (improves performance on proxies with lots of opened tcp connections). See linux tcp(7) TCP_DEFER_ACCEPT or freebsd ACCF_DATA(0). For now linux and freebsd only.

WARNING: the linux TCP_DEFER_ACCEPT is buggy (⇐2.6.23) and doesn't work exactly as expected (if no data is received it will retransmit syn acks for ~ 190 s, irrespective of the set timeout and then it will silently drop the connection without sending a RST or FIN). Try to use it together with tcp_syncnt (this way the number of retrans. SYNACKs can be limited ⇒ the timeout can be controlled in some way).

On FreeBSD:

tcp_defer_accept =  yes | no (default no)

On Linux:

tcp_defer_accept =  number of seconds before timeout (default disabled)

tcp_delayed_ack

Initial ACK for opened connections will be delayed and sent with the first data segment (see linux tcp(7) TCP_QUICKACK). For now linux only.

tcp_delayed_ack  = yes | no (default yes when supported)

tcp_fd_cache

If enabled FDs used for sending will be cached inside the process calling tcp_send (performance increase for sending over tcp at the cost of slightly slower connection closing and extra FDs kept open)

tcp_fd_cache = yes | no (default yes)

tcp_keepalive

Enables keepalive for tcp (sets SO_KEEPALIVE socket option)

tcp_keepalive = yes | no (default yes)

tcp_keepcnt

Number of keepalives sent before dropping the connection (TCP_KEEPCNT socket option). Linux only.

tcp_keepcnt = number (not set by default)

tcp_keepidle

Time before starting to send keepalives, if the connection is idle (TCP_KEEPIDLE socket option). Linux only.

tcp_keepidle  = seconds (not set by default)

tcp_keepintvl

Time interval between keepalive probes, when the previous probe failed (TCP_KEEPINTVL socket option). Linux only.

tcp_keepintvl = seconds (not set by default)

tcp_linger2

Lifetime of orphaned sockets in FIN_WAIT2 state (overrides tcp_fin_timeout on, see linux tcp(7) TCP_LINGER2). Linux only.

tcp_linger2 = seconds (not set by default)

tcp_max_connections

Maximum number of tcp connections (if the number is exceeded no new tcp connections will be accepted). Default is defined in tcp_conn.h: #define DEFAULT_TCP_MAX_CONNECTIONS 2048

Example of usage:

  tcp_max_connections=4096

tcp_no_connect

Stop outgoing TCP connects (also stops TLS) by setting tcp_no_connect to yes. You can do this any time, even even if Kamailio is already started (in this case using sercmd cfg.set_now_int tcp no_connect 1).

tcp_poll_method

Poll method used (by default the best one for the current OS is selected). For available types see io_wait.c and poll_types.h: none, poll, epoll_lt, epoll_et, sigio_rt, select, kqueue, /dev/poll

Example of usage:

  tcp_poll_method=select

tcp_rd_buf_size

Buffer size used for tcp reads. A high buffer size increases performance on server with few connections and lot of traffic on them, but also increases memory consumption (so for lots of connection is better to use a low value). Note also that this value limits the maximum datagram size that can be received over tcp.

Default: 4096, can be changed at runtime.

tcp_send_timeout

Time in seconds after a TCP connection will be closed if it is not available for writing in this interval (and Kamailio wants to send something on it). Lower this value for faster detection of broken TCP connections. The default value is 10s.

Example of usage:

  tcp_send_timeout=3

tcp_source_ipv4, tcp_source_ipv6

Set the source IP for all outbound TCP connections. If setting of the IP fails, the TCP connection will use the default IP address.

tcp_source_ipv4 = IPv4 address
tcp_source_ipv6 = IPv6 address

tcp_syncnt

Number of SYN retransmissions before aborting a connect attempt (see linux tcp(7) TCP_SYNCNT). Linux only.

tcp_syncnt = number of syn retr. (default not set)

tcp_wq_blk_size

Block size used for tcp async writes. It should be big enough to hold a few datagrams. If it's smaller then a datagram (in fact a tcp write()) size, it will be rounded up. It has no influenced on the number of datagrams queued (for that see tcp_conn_wq_max or tcp_wq_max). It has mostly debugging and testing value (can be ignored).

Default: 2100 (~ 2 INVITEs), can be changed at runtime.

tcp_wq_max

Maximum bytes queued for write allowed globally. It has no effect if tcp_write_buf is not enabled.

tcp_wq_max = bytes (default 10 Mb)

SCTP Parameters

disable_sctp

Global parameter to disable SCTP support in the SIP server. see enable_sctp

Default value is 'auto'.

Example of usage:

  disable_sctp=yes

enable_sctp

enable_sctp = 0/1/2  - SCTP disabled (0)/ SCTP enabled (1)/auto (2), 
                       default auto (2)

sctp_children

sctp children no (similar to udp children)

sctp_children = number 

sctp_socket_rcvbuf

Size for the sctp socket receive buffer

Alias name: sctp_socket_receive_buffer

sctp_socket_rcvbuf = number 

sctp_socket_sndbuf

Size for the sctp socket send buffer

Alias name: sctp_socket_send_buffer

sctp_socket_sndbuf = number

sctp_autoclose

Number of seconds before autoclosing an idle association (default: 180 s). Can be changed at runtime, but it will affect only new associations. E.g.:

$ sercmd cfg.set_now_int sctp autoclose 120
sctp_autoclose = seconds

sctp_send_ttl

Number of milliseconds before an unsent message/chunk is dropped (default: 32000 ms or 32 s). Can be changed at runtime, e.g.:

$ sercmd cfg.set_now_int sctp send_ttl 180000
sctp_send_ttl = milliseconds - n

sctp_send_retries

How many times to attempt re-sending a message on a re-opened association, if the sctp stack did give up sending it (it's not related to sctp protocol level retransmission). Useful to improve reliability with peers that reboot/restart or fail over to another machine.

WARNING: use with care and low values (e.g. 1-3) to avoid “multiplying” traffic to unresponding hosts (default: 0).Can be changed at runtime.

sctp_send_retries = 1

sctp_assoc_tracking

Controls whether or not sctp associations are tracked inside Kamailio. Turning it off would result in less memory being used and slightly better performance, but it will also disable some other features that depend on it (e.g. sctp_assoc_reuse). Default: yes.

Can be changed at runtime (sercmd sctp assoc_tracking 0), but changes will be allowed only if all the other features that depend on it are turned off (for example it can be turned off only if first sctp_assoc_reuse was turned off).

Note: turning sctp_assoc_tracking on/off will delete all the tracking information for all the currently tracked associations and might introduce a small temporary delay in the sctp processing if lots of associations were tracked.

Config options depending on sctp_assoc_tracking being on: sctp_assoc_reuse.

sctp_assoc_tracking = yes/no

sctp_assoc_reuse

Controls sctp association reuse. For now only association reuse for replies is affected by it. Default: yes. Depends on sctp_assoc_tracking being on.

Note that even if turned off, if the port in via corresponds to the source port of the association the request was sent on or if rport is turned on (force_rport() or via containing a rport option), the association will be automatically reused by the sctp stack. Can be changed at runtime (sctp assoc_reuse), but it can be turned on only if sctp_assoc_tracking is on.

sctp_assoc_reuse = yes/no

sctp_max_assocs

Maximum number of allowed open sctp associations. -1 means maximum allowed by the OS. Default: -1. Can be changed at runtime (e.g.: sercmd cfg.set_now_int sctp max_assocs 10 ). When the maximum associations number is exceeded and a new associations is opened by a remote host, the association will be immediately closed. However it is possible that some sip packets get through (especially if they are sent early, as part of the 4-way handshake).

When Kamailio tries to open a new association and the max_assocs is exceeded the exact behaviour depends on whether or not sctp_assoc_tracking is on. If on, the send triggering the active open will gracefully fail, before actually opening the new association and no packet will be sent. However if sctp_assoc_tracking is off, the association will first be opened and then immediately closed. In general this means that the initial sip packet will be sent (as part of the 4-way handshake).

sctp_max_assocs = number

sctp_srto_initial

Initial value of the retr. timeout, used in RTO calculations (default: OS specific).

Can be changed at runtime (sctp srto_initial) but it will affect only new associations.

sctp_srto_initial = milliseconds

sctp_srto_max

Maximum value of the retransmission timeout (RTO) (default: OS specific).

WARNING: values lower then the sctp sack_delay will cause lots of retransmissions and connection instability (see sctp_srto_min for more details).

Can be changed at runtime (sctp srto_max) but it will affect only new associations.

sctp_srto_max = milliseconds

sctp_srto_min

Minimum value of the retransmission timeout (RTO) (default: OS specific).

WARNING: values lower then the sctp sack_delay of any peer might cause retransmissions and possible interoperability problems. According to the standard the sack_delay should be between 200 and 500 ms, so avoid trying values lower then 500 ms unless you control all the possible sctp peers and you do make sure their sack_delay is higher or their sack_freq is 1.

Can be changed at runtime (sctp srto_min) but it will affect only new associations.

sctp_srto_min = milliseconds

sctp_asocmaxrxt

Maximum retransmissions attempts per association (default: OS specific). It should be set to sctp_pathmaxrxt * no. of expected paths.

Can be changed at runtime (sctp asocmaxrxt) but it will affect only new associations.

sctp_asocmaxrxt   = number

sctp_init_max_attempts

Maximum INIT retransmission attempts (default: OS specific).

Can be changed at runtime (sctp init_max_attempts).

sctp_init_max_attempts = number

sctp_init_max_timeo

Maximum INIT retransmission timeout (RTO max for INIT). Default: OS specific.

Can be changed at runtime (sctp init_max_timeo).

sctp_init_max_timeo = milliseconds

sctp_hbinterval

sctp heartbeat interval. Setting it to -1 will disable the heartbeats. Default: OS specific.

Can be changed at runtime (sctp hbinterval) but it will affect only new associations.

sctp_hbinterval = milliseconds

sctp_pathmaxrxt

Maximum retransmission attempts per path (see also sctp_asocmaxrxt). Default: OS specific.

Can be changed at runtime (sctp pathmaxrxt) but it will affect only new associations.

sctp_pathmaxrxt = number

sctp_sack_delay

Delay until an ACK is generated after receiving a packet. Default: OS specific.

WARNING: a value higher then srto_min can cause a lot of retransmissions (and strange problems). A value higher then srto_max will result in very high connections instability. According to the standard the sack_delay value should be between 200 and 500 ms.

Can be changed at runtime (sctp sack_delay) but it will affect only new associations.

sctp_sack_delay = milliseconds

sctp_sack_freq

Number of packets received before an ACK is sent (without waiting for the sack_delay to expire). Default: OS specific.

Note: on linux with lksctp up to and including 1.0.9 is not possible to set this value (having it in the config will produce a warning on startup).

Can be changed at runtime (sctp sack_freq) but it will affect only new associations.

sctp_sack_freq = number

sctp_max_burst

Maximum burst of packets that can be emitted by an association. Default: OS specific.

Can be changed at runtime (sctp max_burst) but it will affect only new associations.

sctp_max_burst = number

Blacklist Parameters

dst_blacklist_expire

Alias name: dst_blacklist_ttl

How much time a blacklisted destination will be kept in the blacklist (w/o any update).

dst_blacklist_expire = time in s (default 60 s)

dst_blacklist_gc_interval

How often the garbage collection will run (eliminating old, expired entries).

dst_blacklist_gc_interval = time in s (default 60 s)

dst_blacklist_init

If off, the blacklist is not initialized at startup and cannot be enabled runtime, that saves some memory.

dst_blacklist_init = on | off (default on)

dst_blacklist_mem

Maximum shared memory amount used for keeping the blacklisted destinations.

dst_blacklist_mem = size in Kb (default 250 Kb)

use_dst_blacklist

Enable the destination blacklist: Each failed send attempt will cause the destination to be added to the blacklist. Before any send, this blacklist will be checked and if a match is found, the send is no longer attempted (an error is returned immediately).

Note: using the blacklist incurs a small performance penalty.

See also doc/dst_blacklist.txt.

use_dst_blacklist = on | off (default off)

Real-Time Parameters

real_time

Sets real time priority for all the ser processes, or the timers (bitmaks).

   Possible values:   0  - off
                      1  - the "fast" timer
                      2  - the "slow" timer
                      4  - all processes, except the timers
   Example: real_time= 7 => everything switched to real time priority.
real_time = <int> (flags) (default off)

rt_policy

Real time scheduling policy, 0 = SCHED_OTHER, 1= SCHED_RR and 2=SCHED_FIFO

rt_policy= <0..3> (default 0)

rt_prio

Real time priority used for everything except the timers, if real_time is enabled.

rt_prio = <int> (default 0)

rt_timer1_policy

Alias name: rt_ftimer_policy

Like rt_policy but for the “fast” timer.

rt_timer1_policy=<0..3> (default 0)

rt_timer1_prio

Alias name: rt_fast_timer_prio, rt_ftimer_prio

Like rt_prio but for the “fast” timer process (if real_time & 1).

   
rt_timer1_prio=<int> (default 0)

rt_timer2_policy

Alias name: rt_stimer_policy

Like rt_policy but for the “slow” timer.

rt_timer2_policy=<0..3> (default 0)

rt_timer2_prio

Alias name: rt_stimer_prio

Like rt_prio but for the “slow” timer.

rt_timer2_prio=<int> (default 0)

Core functions

Functions exported by core that can be used in route blocks.

add_local_rport

Add rport parameter to local generated Via header – see RFC3581. In effect for forwarded SIP requests.

Example of usage:

add_local_rport();

append_branch

Similarly to t_fork_to, it extends destination set by a new entry. The difference is that current URI is taken as new entry.

Without parameter, the function copies the current URI into a new branch. Thus, leaving the main branch (the URI) for further manipulation.

With a parameter, the function copies the URI in the parameter into a new branch. Thus, the current URI is not manipulated.

Note that it's not possible to append a new branch in “on_failure_route” block if a 6XX response has been previously received (it would be against RFC 3261).

Example of usage:

    # if someone calls B, the call should be forwarded to C too.
    #
    if (method=="INVITE" && uri=~"sip:B@xx.xxx.xx ")
    {
        # copy the current branch (branches[0]) into
        # a new branch (branches[1])
        append_branch();
        # all URI manipulation functions work on branches[0]
        # thus, URI manipulation does not touch the 
        # appended branch (branches[1])
        seturi("sip:C@domain");
        
        # now: branch 0 = C@domain
        #      branch 1 = B@xx.xx.xx.xx
        
        # and if you need a third destination ...
        
        # copy the current branch (branches[0]) into
        # a new branch (branches[2])
        append_branch();
        
        # all URI manipulation functions work on branches[0]
        # thus, URI manipulation does not touch the 
        # appended branch (branches[1-2])
        seturi("sip:D@domain");
        
        # now: branch 0 = D@domain
        #      branch 1 = B@xx.xx.xx.xx
        #      branch 2 = C@domain
        
        t_relay();
        exit;
    };

    # You could also use append_branch("sip:C@domain") which adds a branch with the new URI:
    
    
    if(method=="INVITE" && uri=~"sip:B@xx.xxx.xx ") {
        # append a new branch with the second destionation
        append_branch("sip:user@domain");
        # now: branch 0 = B@xx.xx.xx.xx
        # now: branch 1 = C@domain

        t_relay();
        exit;
}

avpflags

break

Since v0.10.0-dev3, 'break' can no longer be used to stop the execution of a route. The only place to use is to end a 'case' block in a 'switch' statement. 'return' must be now used instead of old 'break'.

'return' and 'break' have now a similar meaning as in c/shell.

drop

Stop the execution of the configuration script and alter the implicit action which is done afterwards.

If the function is called in a 'branch_route' then the branch is discarded (implicit action for 'branch_route' is to forward the request).

If the function is called in a 'onreply_route' then any provisional reply is discarded (implicit action for 'onreply_route' is to send the reply upstream according to Via header).

Example of usage:

  onreply_route {
      if(status=="183") {
          drop();
      }
  }

exit

Stop the execution of the configuration script – it has the same behaviour as return(0). It does not affect the implicit action to be taken after script execution.

route {
  if (route(2)) {
    xlog("L_NOTICE","method $rm is INVITE\n");
  } else {
    xlog("L_NOTICE","method is $rm\n");
  };
}
route[2] {
  if (is_method("INVITE")) {
    return(1);
  } else if (is_method("REGISTER")) {
    return(-1);
  } else if (is_method("MESSAGE")) {
    sl_send_reply("403","IM not allowed");
    exit;
  };
}

error

exec

force_rport

Force_rport() adds the rport parameter to the first Via header of the received message. Thus, Kamailio will add the received port to the top most via header in the SIP message, even if the client does not indicate support for rport. This enables subsequent SIP messages to return to the proper port later on in a SIP transaction.

This is useful for NAT traversal, to enforce symmetric response signaling.

The rport parameter is defined in RFC 3581.

Note: there is also a force_rport parameter which changes the gobal behavior of the SIP proxy.

Example of usage:

  force_rport();

add_rport

Alias for force_rport();

force_send_socket

Force OpenSER to send the message from the specified socket (it _must_ be one of the sockets OpenSER listens on). If the protocol doesn't match (e.g. UDP message “forced” to a TCP socket) the closest socket of the same protocol is used.

Example of usage:

  force_send_socket(10.10.10.10:5060);

force_tcp_alias

Alias name: add_tcp_alias

force_tcp_alias(port)

adds a tcp port alias for the current connection (if tcp). Usefull if you want to send all the trafic to port_alias through the same connection this request came from [it could help for firewall or nat traversal]. With no parameters adds the port from the message via as the alias. When the “aliased” connection is closed (e.g. it's idle for too much time), all the port aliases are removed.

forward

Forward the SIP request to the given destination in stateless mode. This has the format of [proto:]host[:port]. Host can be an IP or hostname; supported protocols are UDP, TCP and TLS. (For TLS, you need to compile the TLS support into core). If proto or port are not specified, NAPTR and SRV lookups will be used to determine them (if possible). Its important to keep in mind that this information is cached, so any changes in the DNS setup for this name during the runtime of the server are not recognized. If you want to avoid this, set the destination URI or request URI and call forward without parameters instead.

If the destination parameter is missing and no destination URI is set as well then the forwarding will be done based on the request URI.

Example of usage:

  forward("10.0.0.10:5060");
  #or
  forward();

forward_sctp

forward_tcp

forward_tls

forward_udp

isavpflagset

isflagset

Test if a flag is set for current processed message (if the flag value is 1). The value of the parameter can be in range of 0..31.

For more see http://www.kamailio.org/dokuwiki/doku.php/tutorials:openser-flag-operations or flags.

Example of usage:

  if(isflagset(3)) {
      log("flag 3 is set\n");
  };

SIP-Router also supports named flags. They have to be declared at the beginning of the config file with:

 flags  flag1_name[:position],  flag2_name ...

Example:

     flags test, a:1, b:2 ;
     route{
            setflag(test);
            if (isflagset(a)){ # equiv. to isflagset(1)
              ....
            }
            resetflag(b);  # equiv. to resetflag(2) 

log

Write text message to standard error terminal or syslog. You can specify the log level as first parameter.

For more see: http://www.kamailio.org/dokuwiki/doku.php/tutorials:debug-syslog-messages

Example of usage:

  log("just some text message\n");

prefix

Add the string parameter in front of username in R-URI.

Example of usage:

  prefix("00");

resetavpflag

resetflag

return

The return() function allows you to return any integer value from a called route() block. You can test the value returned by a route using $retcode or $? variable.

return(0) is same as exit();

In bool expressions:

If no value is specified, or a route reaches its end without executing a return statement, it returns 1. If return is used in the top level route is equivalent with exit [val].

Example usage:

route {
  if (route(2)) {
    xlog("L_NOTICE","method $rm is INVITE\n");
  } else {
    xlog("L_NOTICE","method $rm is REGISTER\n");
  };
}
route[2] {
  if (is_method("INVITE")) {
    return(1);
  } else if (is_method("REGISTER")) {
    return(-1);
  } else {
    return(0);
  };
}

revert_uri

Set the R-URI to the value of the R-URI as it was when the request was received by server (undo all changes of R-URI).

Example of usage:

  revert_uri();

rewritehostport

Alias name: sethostport, sethp

Rewrite the domain part and port of the R-URI with the value of function's parameter. Other parts of the R-URI like username and URI parameters remain unchanged.

Example of usage:

  rewritehostport("1.2.3.4:5080");

rewritehostporttrans

Alias name: sethostporttrans, sethpt

Rewrite the domain part and port of the R-URI with the value of function's parameter. Also allows to specify the transport parameter. Other parts of the R-URI like username and URI parameters remain unchanged.

Example of usage:

  rewritehostporttrans(???"1.2.3.4:5080"???);

rewritehost

Alias name: sethost, seth

Rewrite the domain part of the R-URI with the value of function's parameter. Other parts of the R-URI like username, port and URI parameters remain unchanged.

Example of usage:

  rewritehost("1.2.3.4");

rewriteport

Alias name: setport, setp

Rewrites/sets the port part of the R-URI with the value of function's parameter.

Example of usage:

  rewriteport(5070);

rewriteuri

Alias name: seturi

Rewrite the request URI.

Example of usage:

  rewriteuri("sip:test@openser.org");

rewriteuserpass

Alias name: setuserpass, setup

Rewrite the password part of the R-URI with the value of function's parameter.

Example of usage:

  rewriteuserpass("my_secret_passwd");

rewriteuser

Alias name: setuser, setu

Rewrite the user part of the R-URI with the value of function's parameter.

Example of usage:

  rewriteuser("newuser");

send

Send the original SIP message to a specific destination in stateless mode. No changes are applied to received message, no Via header is added. Host can be an IP or hostname. Used protocol: UDP

Parameter is mandatory and has string format.

Example of usage:

 send("10.10.10.10:5070");

send_tcp

Send the original SIP message to a specific destination in stateless mode. No changes are applied to received message, no Via header is added. Host can be an IP or hostname. Used protocol: UDP

Parameter is mandatory and has string format.

Example of usage:

 send_tcp("10.10.10.10:5070");

set_advertised_address

Same as 'advertised_address' but it affects only the current message. It has priority if 'advertised_address' is also set.

Example of usage:

  set_advertised_address("openser.org");

set_advertised_port

Same as 'advertised_port' but it affects only the current message. It has priority over 'advertised_port'.

Example of usage:

  set_advertised_port(5080);

set_forward_no_connect

The message will be forwarded only if there is already an existing connection to the destination. It applies only to connection oriented protocols like TCP and TLS (TODO: SCTP), for UDP it will be ignored. The behavior depends in which route block the function is called:

Example of usage:

  route {
    ...
    if (lookup()) {
      //requests to local users. They are usually behind NAT so it does not make sense to try
      //to establish a new TCP connection 
      set_forward_no_connect();
      t_relay();
    }
    ...
  }

set_forward_close

Try to close the connection (the one on which the message is sent out) after forwarding the current message. Can be used in same route blocks as set_forward_no_connect().

Note: Use with care as you might not receive the replies anymore as the connection is closed.

set_reply_no_connect

Like set_forward_no_connect(), but for replies to the current message (local generated replies and replies forwarded by tm). The behavior depends in which route block the function is called:

Example of usage:

  route[4] {
    //requests from local users. There are usually behind NAT so it does not make sense to try
    //to establish a new TCP connection for the replies
    set_reply_no_connect();
    // do authentication and call routing
    ...
  }

set_reply_close

Like set_reply_no_connect, but closes the TCP connection after sending. Can be used in same route blocks as set_reply_no_connect.

Example of usage:

  route {
    ...
    if (...caller-is-not-registered...) {
      // reject unregistered client
      // if request was received via TCP/TLS close the connection, as
      // this may trigger re-registration of the client.
      set_reply_close();
      sl_send_reply("403","REGISTER first");
      exit;
    }
    ...
  }

setavpflag

setflag

Set a flag for current processed message. The value of the parameter can be in range of 0..31. The flags are used to mark the message for special processing (e.g., accounting) or to keep some state (e.g., message authenticated).

For more see http://www.kamailio.org/dokuwiki/doku.php/tutorials:openser-flag-operations .

Example of usage:

  setflag(3);

strip

Strip the first N-th characters from username of R-URI (N is the value of the parameter).

Example of usage:

  strip(3);

strip_tail

Strip the last N-th characters from username of R-URI (N is the value of the parameter).

Example of usage:

strip_tail(3);

udp_mtu_try_proto(proto)

Example:

if($rd=="10.10.10.10")
    udp_mtu_try_proto(SCTP);

userphone

Routing blocks

SIP-Router has support for named routes. Names can be used instead of numbers in all the route commads or route declarations.

Note: route(number) is equivalent to route(“number”)

Example:

route{
  ...
  route("test");
  ...
}
route["test"]{
  ...
}

route

Request routing block. It contains a set of actions to be taken for SIP requests.

The main 'route' block identified by 'route{…}' or 'route[0]{…}' is executed for each SIP request.

The implicit action after execution of the main route block is to drop the SIP request. To send a reply or forward the request, explicit actions must be called inside the route block.

Example of usage:

    route {
         if(is_method("OPTIONS")) {
            # send reply for each options request
            sl_send_reply("200", "ok");
            exit();
         }
         route(1);
    }
    route[1] {
         # forward according to uri
         forward();
    }

branch_route

Request's branch routing block. It contains a set of actions to be taken for each branch of a SIP request. It is executed only by TM module after it was armed via t_on_branch(“branch_route_index”).

Example of usage:

    route {
        lookup("location");
        t_on_branch("1");
        if(!t_relay()) {
            sl_send_reply("500", "relaying failed");
        }
    }
    branch_route[1] {
        if(uri=~"10\.10\.10\.10") {
            # discard branches that go to 10.10.10.10
            drop();
        }
    }

failure_route

Failed transaction routing block. It contains a set of actions to be taken each transaction that received only negative replies (>=300) for all branches. The 'failure_route' is executed only by TM module after it was armed via t_on_failure(“failure_route_index”).

Note that in 'failure_route' is processed the request that initiated the transaction, not the reply .

Example of usage:

    route {
        lookup("location");
        t_on_failure("1");
        if(!t_relay()) {
            sl_send_reply("500", "relaying failed");
        }
    }
    failure_route[1] {
        if(is_method("INVITE")) {
             # call failed - relay to voice mail
             t_relay_to_udp("voicemail.server.com","5060");
        }
    }

onreply_route

Reply routing block. It contains a set of actions to be taken for SIP replies.

The main 'onreply_route' identified by 'onreply_route {…}' or 'onreply_route[0] {…}' is executed for all replies received.

Certain 'onreply_route' blocks can be executed by TM module for special replies. For this, the 'onreply_route' must be armed for the SIP requests whose replies should be processed within it, via t_on_reply(“onreply_route_index”).

Main 'onreply_route' block is executed before a possible tm 'onreply_route' block.

  route {
      lookup("location");
      t_on_reply("1");
      if(!t_relay()) {
          sl_send_reply("500", "relaying failed");
      }
  }
 
  onreply_route {
      if(!t_check_trans()) {
          drop;
      }
  }
 
  onreply_route[1] {
      if(status=~"1[0-9][0-9]") {
           log("provisional response\n");
      }
  }

onsend_route

The route is executed in when a SIP request is sent out. Only a limited number of commands are allowed (drop, if + all the checks, msg flag manipulations, send(), log(), textops::search()).

In this route the final destination of the message is available an can be checked (with snd_ip, snd_port, to_ip, to_port, snd_proto, snd_af).

This route is executed only when forwarding requests - it is not executed for replies, retransmissions, or locally generated messages (e.g. via fifo uac).

Example:

onsend_route{
  if(to_ip==1.2.3.4 && !isflagset(12)){
    log(1, "message blocked\n");
    drop;
  }
}

event_route

Generic type of route executed when specific events happen.

Prototype: event_route[groupid:eventid]

Implementations:

modparam("htable", "htable", "a=>size=4;")
 
event_route[htable:mod-init] {
  $sht(a=>calls-to::10.10.10.10) = 0;
  $sht(a=>max-calls-to::10.10.10.10) = 100;
}
 
route {
  if(is_method("INVITE") && !has_totag())
  {
    switch($rd) {
      case "10.10.10.10":
        lock("calls-to::10.10.10.10");
        $sht(a=>calls-to::10.10.10.10) =
            $sht(a=>calls-to::10.10.10.10) + 1;
        unlock("calls-to::10.10.10.10");
        if($sht(a=>calls-to::10.10.10.10)>$sht(a=>max-calls-to::10.10.10.10))
        {
           sl_send_reply("500", "To many calls to .10");
           exit;
        }
      break;
      ...
    }
  }
}

Script statements

if

IF-ELSE statement

Prototype:

    if(expr) {
       actions;
    } else {
       actions;
    }

The 'expr' should be a valid logical expression.

The logical operators that can be used in 'expr':

* == - equal * != - not equal * =~ - regular expression matching * !~ - regular expression not-matching * > - greater * >= - greater or equal * < - less * ⇐ - less or equal * && - logical AND * || - logical OR * ! - logical NOT * [ … ] - test operator - inside can be any arithmetic expression

Example of usage:

  if(is_method("INVITE"))
  {
      log("this sip message is an invite\n");
  } else {
      log("this sip message is not an invite\n");
  }

switch

SWITCH statement - it can be used to test the value of a pseudo-variable.

IMPORTANT NOTE: 'break' can be used only to mark the end of a 'case' branch (as it is in shell scripts). If you are trying to use 'break' outside a 'case' block the script will return error – you must use 'return' there.

Example of usage:

    route {
        route(1);
        switch($retcode)
        {
            case -1:
                log("process INVITE requests here\n");
            break;
            case 1:
                log("process REGISTER requests here\n");
            break;
            case 2:
            case 3:
                log("process SUBSCRIBE and NOTIFY requests here\n");
            break;
            default:
                log("process other requests here\n");
       }

        # switch of R-URI username
        switch($rU)
        {
            case "101":
                log("destination number is 101\n");
            break;
            case "102":
                log("destination number is 102\n");
            break;
            case "103":
            case "104":
                log("destination number is 103 or 104\n");
            break;
            default:
                log("unknown destination number\n");
       }
    }

    route[1]{
        if(is_method("INVITE"))
        {
            return(-1);
        };
        if(is_method("REGISTER"))
            return(1);
        }
        if(is_method("SUBSCRIBE"))
            return(2);
        }
        if(is_method("NOTIFY"))
            return(3);
        }
        return(-2);
    }

NOTE: take care while using 'return' - 'return(0)' stops the execution of the script.

while

while statement

Example of usage:

  
  $var(i) = 0;
  while($var(i) < 10)
  {
      xlog("counter: $var(i)\n");
      $var(i) = $var(i) + 1;
  }

Script operations

Assignments together with string and arithmetic operations can be done directly in configuration file.

Assignment

Assignments can be done like in C, via '=' (equal). The following pseudo-variables can be used in left side of an assignment: * AVPs - to set the value of an AVP * script variables ($var(…)) - to set the value of a script variable * shared variables ($shv(…)) * $ru - to set R-URI * $rd - to set domain part of R-URI * $rU - to set user part of R-URI * $rp - to set the port of R-URI * $du - to set dst URI * $fs - to set send socket * $br - to set branch * $mf - to set message flags value * $sf - to set script flags value * $bf - to set branch flags value

$var(a) = 123;

There is a special assign operator ':=' (colon equal) that can be used with AVPs. If the right value is 'null', all AVPs with that name are deleted. If different, the new value will overwrite any existing values for the AVPs with than name (on other words, delete existing AVPs with same name, add a new one with the right side value).

$avp(i:3) := 123;

String operations

For strings, '+' is available to concatenate.

$var(a) = "test";
$var(b) = "sip:" + $var(a) + "@" + $fd;

Arithmetic operations

For numbers, one can use:

* + : plus * - : minus * / : divide * * : multiply * % : modulo * | : bitwise OR * & : bitwise AND * ^ : bitwise XOR * ~ : bitwise NOT * « : bitwise left shift * » : bitwise right shift

Example:

$var(a) = 4 + ( 7 & ( ~2 ) );

NOTE: to ensure the priority of operands in expression evaluations do use parenthesis.

Arithmetic expressions can be used in condition expressions:

if( $var(a) & 4 )
    log("var a has third bit set\n");

Operators

  1. type casts operators: (int), (str).
  2. string comparison: eq, ne
  3. integer comparison: ieq, ine
Note: The names are not yet final (use them at your own risk).
Future version might use ==/!= only for ints (ieq/ine) and eq/ne for strings
(under debate). They are almost equivalent to == or !=, but they force the
conversion of their operands (eq to string and ieq to int), allowing among
other things better type checking on startup and more optimizations.

Non equiv. examples:

0 == "" (true) is not equivalent to 0 eq "" (false: it evaluates to "0" eq "").

"a" ieq "b" (true: (int)"a" is 0 and (int)"b" is 0) is not equivalent to "a" == "b" (false).

Note: internally == and != are converted on startup to eq/ne/ieq/ine  whenever possible
 (both operand types can be safely determined at start time and they are the same). 

  - kamailio tries to guess what the user wanted when operators that support multiple
types are used on different typed operands. In general convert the right operand to the
type of the left operand and then perform the operation. Exception: the left operand is
undef. This applies to the following operators: +, == and !=.
     Special case: undef as left operand:
     For +: undef + expr -> undef is converted to string => "" + expr.
     For == and !=:   undef == expr -> undef is converted to type_of expr.
     If expr is undef, then undef == undef is true (internally is converted
     to string).

  - expression evaluation changes: kamailio will auto-convert to integer or string
    in function of the operators: 
       int(undef)==0,  int("")==0, int("123")==123, int("abc")==0
       str(undef)=="", str(123)=="123".

  - script operators for dealing with empty/undefined variables
      defined expr - returns true if expr is defined, and false if not.
                     Note: only a standalone avp or pvar can be
                     undefined, everything else is defined.
      strlen(expr) - returns the lenght of expr evaluated as string.
      strempty(expr) - returns true if expr evaluates to the empty
                       string (equivalent to expr=="").
      Example: if (defined $v && !strempty($v)) $len=strlen($v);